Getting Familiar with Plumbing: A Must for Installing a Bathtub
Getting Familiar with Plumbing: A Must for Installing a Bathtub
Blog Article
Everybody maintains his or her own thinking about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bath tub isn't precisely rocket science, however it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is additionally a reasonably difficult project. If the old bathtub is readily easily accessible, the project can move easily; if you need to open a wall to get rid of the old tub as well as position the new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will need a helper to leave the old bathtub and set in the new one. Make certain you have actually certified on your own for the task as well as fit trying it. Rather than employing a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you begin. Possibilities are you might need an expert plumber to make tube connections.
This write-up will aid you set up a brand-new bath tub in your washroom if you have actually already purchased a new bathtub and also do not require to alter the plan of your previous water supply pipes.
Your devices and material list should comprise the following:
Preparing for the Setup
First of all, the sustaining structure supplied with the bath needs to be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps device to stop stress on the bathtub.
Fit the versatile tap adapters to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should now prepare to be suited its final placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water system. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of getting rid of the existing taps can be quite problematic because of the limited accessibility that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. When the supply pipes have actually been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before proceeding to fit the new faucets, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Using both wood boards under its feet, put the bath tub in the needed setting. The wood boards are valuable in equally spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the bathtub till the level checks out level.
To mount taps, fit the bottom of the furthest versatile tap connector to the ideal supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as check all joints and also brand-new pipework for leaks and also tighten them if needed. Fill up the bath tub and also examine the overflow outlet and also the typical outlet for leaks.
Finally, repair the bathroom paneling as defined in the maker's instruction manual. Tiling as well as securing around the bathtub ought to wait until the tub has actually been made use of at the very least when as this will resolve it right into its final placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making sure that the washing machines remain in location in between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet connectors. The previous type should be connected to the tap ends initially, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to split a rigid seal, causing the water to pass through the wall in between the bathroom and also the tiling, resulting in difficulties with wetness and also possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are offered in tubes and also cartridges, and are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealer can split fairly very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the market. It is suggested to fit the tiles using water-resistant or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our excerpt on How to Install a Bathtub. Thanks so much for taking time to read our post. If you enjoyed our blog posting please remember to pass it around. We take joy in reading our article about How to Install a Bathtub.
The right fix? Ring! Report this page